Принтер лазерный Samsung Xpress M2020, ч/б, A4 — 2344 отзывов, плюсы и минусы
2344 отзывов пользователей о Samsung Xpress M2020, ч/б, A4
Пользовались
Samsung Xpress M2020, ч/б, A4?
Поделитесь своим опытом и помогите другим сделать правильный выбор
- + Компактный. В теории печать с телефона (при наличии установленного софта)
- - Одна серьезная фича (по мнению производителей), а на мой взгляд - серьезный баг. Если ошибся с количеством копий (например надо 100 штук, а ты вложил 99листов, или надо 2, а ты вложил 1 лист), принтер пробует захватить след.лист, но при...
- + Компактный, шустрый.
- - На втором покупном картридже, примерно через 5 лет, стал забирать второй лист и...
- + Безотказный работает уже 12 лет, в 2019 году заменил стартовый картридж на новый, до этого стартовый картридж заправлял сам предварительно сменив прошивку; напечатано 296 710 страниц, рефераты, курсовые, доклады и диплом, в итоге фотобарабан стерся пошла полоса по центру, пришлось заменить на новый картридж за 350 рублей, теперь ещё 12 лет проработает, Сейчас 2021 год апрель работает отлично без проблем, пришлось почистить соленоиды от старых прокладок, начали залипать за 13 лет использования...
- - Плохо работает захват бумаги, особенно при двухсторонней печати
- + Мне достался по наследству такой принтер. Вообще хороший принтер ремонт простой
картриджи чипоканные но заправляються очень просто в домашних условиях и видео как это делаеться я покажу. Нужен програматор. https://youtu...
- + Принтер был куплен в 2008 году и работает по сей день.
- - А нет их.
- + Купил лет 10 назад на авито за 500р. Почистил и перевернул резиновый ролик подачи бумаги и обслужил родной картридж. 10 лет гонял, бед не знал. Сейчас опять ролику тяжко цеплять бумагу стало, помогать приходится. И картридж тускловато печать стал. Кажись тонер кончился и барабан устал.
Желания экспериментировать с современными поделками, заточенными под регулярное "обслуживание" совсем нет. Так уж и быть, поменяю ролик на новый. И картридж на переборку отдам. А может - даже новый куплю! Пусть дальше гоняет :)
- + Отличный товар , всегда под рукой , небольшой размер и полный функционал для офиса , спасибо буду еще заказывать !
- - Чип. Но это, к счастью, решается, хотя все равно удорожает заправку.
- + Недолго греется. Печатает шустро. Приятный внешний вид. Есть верхний лоток - можно копировать сразу...
The instructions also say to use the correct amount of toner for your cartridge, but I was unable to find anywhere on the website where the amount of toner to be used for any particular cartridge was listed. I just used the entire amount that was shipped to me. I suppose I would have stopped trying to fill my cartridge if it had overflowed before accepting all the toner that was shipped to me. Luckily that did not happen.
After the cartridge was refilled, the new chip was installed, and the refilled cartridge was inserted into the printer, the printer went through a rather lengthy reset process before it came back online and was ready to print. (The exact same process may occur when a brand new cartridge is inserted, but since refilling my own cartridge was a new experience to me I was a bit nervous that the process would fail somehow.)
I printed a test page and everything looked great, then I used the Samsung utility to check on the status of the cartridge. It showed that a new cartridge had been installed and that I had approximately 1500 pages left to print. If I actually get anywhere near 1500 pages for a $6.50 investment in toner instead of a $65 investment in a new cartridge I will be very happy indeed.
I'm a bit skeptical about how well the tape will hold the whole thing together, but so far it's working fine.
I'm not too confident that the tape used to re-attach the side of the toner cartridge that needed to be removed will hold given the heat the gets generated by the printer, but after a week or so of use everything is as good as new.
If you don't mind rolling up your sleeves, putting on rubber gloves and making a bit of a mess, you can save yourself quite a bit of money using this refill kit.
1. The instructions were really confusing, but the pictures made it possible. (For example, Step #3 "You can make a hole using a hole making tool" Step #4 "Or depending on the cartridge no hole may be necessary")
2. As I removed the screws, 2 of the screws were completely stripped out, making it nearly impossible to take the thing apart. Once I got it apart, I couldn't get it back together "tight" enough.
3. I got black ink toner (which is a fine, fine black dust) EVERYWHERE while emptying the cartridge (carefully) and then the cap didn't fit the squeeze bottle at all, so the toner poofed out of the neck of the bottle while I tried to fill it. THIS PART WAS SUCH A HUGE MESS!!! It was easily wiped up, but still...
4. After I FINALLY got the cartridge refilled, it won't work AT ALL. It will ONLY print solid black pages, no words, no nothing. I tried to do some troubleshooting with the seller over email and he is also baffled. I've tried all sorts of things with no luck, no error messages, just page after page of black ink. I now have to buy a completely new cartridge and start over.
IN CONCLUSION: I will try this again because it really is cheap and not very hard to do (once you do it once, you'll be a pro).
I will say that the housing the holds the chip the printer uses to validate the cartridge broke off as I removed the packaging and it took a little McGyvering to get it to lock in place. For that I took off a star because without that chip the cartridge is essentially unusable and I'd have to complete an RMA process to get it replaced.




