Дисковая пила Worx WX437, 800 Вт — 154 отзывов, плюсы и минусы
154 отзывов пользователей о Worx WX437, 800 Вт
Пользовались
Worx WX437, 800 Вт?
Поделитесь своим опытом и помогите другим сделать правильный выбор
TimD
31.01.2023
8/10
Оценка пользователя
Хорошо
Was impressed
Bought this to cut floor tiles when laying new kitchen floor. Was a little sceptical about buying a combined tile/wood saw rather than a specific tile saw. But figured being a keen woodworker I would get more use from this once I finished the tiling. Cut 17 full width cuts on 333x333x9mm ceramic floors tiles, plus a few smaller cuts on a single blade. Was very impressed with the ease at which the saw went through the tiles. Admittedly it does now need a new blade, the last couple of cuts took a little longer. Still not bad going. Have yet to try on wood, will use on sheet material most likley, will update review when I do.
Keith
31.01.2023
6/10
Оценка пользователя
Плохо
Not the best for holding
Unfortunately I thought i was getting a good saw to help cut in to floorboards but discovered that the on switch to be a littleout of range to hold the saw correctly and use the trigger at the same time. Has a tendancy to not cut very straight without a lot of effort needed to hold the saw well in place while cutting. Not so easy to use unless for very light work.
Kingman
04.05.2023
8/10
Оценка пользователя
Хорошо
Как говорится в нем
Купил это после того, как просмотрел множество разных до такой степени, что начал сам себя сбивать с толку. Итак, YouTube перешел к повторному просмотру, просмотрел множество обзоров и остановился на этом. Очень удобен в использовании, для его запуска достаточно нажать 2 кнопки, затем только 1. Лазер... как приятное дополнение, это ни в малейшей степени не помогло, так что вы могли бы купить это дешевле без лазера. Я делал полки, и они проходили сквозь доски толщиной 1/2 дюйма, как горячий нож сквозь масло. Поставляется в очень красивом футляре с дополнительными лезвиями... 8/10. Я бы порекомендовал.
Bodkin
31.01.2023
6/10
Оценка пользователя
Плохо
The worx saw explained
Firstly I should explain that I have been using and caring for powered circular saws of all types since 1962 in my trade as a carpenter and joiner, now retied but having time to work on my own house for a change. I bought this worx saw to do some tasks more suited to a saw of this design, when it arrived and I used it for the first time it was imediately completely useless, within the first ten seconds it was clear to me that the supplied blade was faulty, on close inspection I could see it had been manufactured incorrectly with all of the teeth "set" to one side and not each one set to alternate sides of the blade as they should be ( I actually re set the teeth with my own specialised tool) phoned Amazon explaind the prob and was refunded the cost of another blade, the original blade that I "re set" is still in the saw and has done a lot of work, and so far the the saw and blade are now excellent !! I can recomend IF you get a correctly made blade. PLEASE DONT ATTEMPT TO RE SET A CIRCULAR SAW UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING !!!!! 3stars but only because of the blade prob.
Kindle Customer
31.01.2023
6/10
Оценка пользователя
Плохо
Second time lucky
Liked the saw and its ease of use, but the first one only lasted a few months of infrequent use. Amazon replaced it very efficiently and quickly so time will tell how long this one will last.
unwise one
31.01.2023
10/10
Оценка пользователя
Великолепно
Great buy
I bought this for general diy jobs as found a general circular saw too cumbersome.
I decided to try and tile a hearth and then realised this had a diamond tile cutter disc. I used a general tile cutter for most cuts but this came into its own for small cuts, such as the few mm needed to be removed from a 9mm thick porcelain tile.
I thought about a cordless version but I don’t really have plans to use away from home so this is great.
I would buy again.
I decided to try and tile a hearth and then realised this had a diamond tile cutter disc. I used a general tile cutter for most cuts but this came into its own for small cuts, such as the few mm needed to be removed from a 9mm thick porcelain tile.
I thought about a cordless version but I don’t really have plans to use away from home so this is great.
I would buy again.
MPH
31.01.2023
6/10
Оценка пользователя
Плохо
Very disappointed.
Bought this specifically for long cust in laminate flooring, on which it's a dream to use; same for other thin[ish] materials.
I was cooncerned about other reviews stating how difficult/impossible it was to cur a straight line. As it happens, I tried to trim the bottom off a door - didn't have my full size saw with me. It was tough going and I couldn't keep to a stright line but this saw isn't built for that, so can't complain.
The only down sides so far is that the on/off switch is tricky to operate one handed. Only a minor issue and not worthy of a dropped star. Same with the blades being unavailable at stores.
The good sides = Nice big sturdy case that will close without having to tie up the cable - Laser works well and I guess the batteries will last so long as I remember to switch it off.
EDIT Have now used it to cut the long edges of 12mm laminate. Impossible to cut in a straight line. I'm not a carpenter but as experienced with cutting wood. Don't know why I couldn't cut a straight line, just glad I had a plunge saw with me. Not glad it was a few days over the month money back period.
I was cooncerned about other reviews stating how difficult/impossible it was to cur a straight line. As it happens, I tried to trim the bottom off a door - didn't have my full size saw with me. It was tough going and I couldn't keep to a stright line but this saw isn't built for that, so can't complain.
The only down sides so far is that the on/off switch is tricky to operate one handed. Only a minor issue and not worthy of a dropped star. Same with the blades being unavailable at stores.
The good sides = Nice big sturdy case that will close without having to tie up the cable - Laser works well and I guess the batteries will last so long as I remember to switch it off.
EDIT Have now used it to cut the long edges of 12mm laminate. Impossible to cut in a straight line. I'm not a carpenter but as experienced with cutting wood. Don't know why I couldn't cut a straight line, just glad I had a plunge saw with me. Not glad it was a few days over the month money back period.
Amazon Customer
31.01.2023
8/10
Оценка пользователя
Хорошо
Probably as good as it gets
Quite a chunky tool which was not uncomfortable or hard to hold. Slightly disappointed with the accuracy, ended up clamping a betten to use as a guide as it is easy to wander from a straight line making a freehand cut. Coped with chipboard loft flooring if careful to keep a straight cut but did tend to struggle if I wandered off the straight and true. Having only a short base plate did not seem to help. Still pleased with this tool and look forward to trying it on mild steel sheets and other types of wood which I think will give a better result and an easier cut.
RoboPop
31.01.2023
10/10
Оценка пользователя
Великолепно
A Very Useful and Smug Purchase
I have various DIY tools that don't get much use but always on hand and this tool has seen some serious use since I bought it. From trimming MDF shelves to a ton of decking in my/son's garden, along with fence panels and posts. As far as I'm concerned it's paid for itself several times over just in terms of speed.
Very easy to use and I have found the cutting guide rail (included) to be very useful indeed. I'm lucky in that I can easily use it one handed but appreciate that someone with small hands may experience problems, as the handle is quite thick since it houses the motor. The included blade is brilliant, having said that, I have only used it for cutting wood of various thickness. Another caveat is the cutting depth which is about 26mm - all the decking I cut was 28mm thick, however the cut was deep and precise enough to simply snap the ends off. For some fence posts I simply rotated them and cut from the other side - easy.
My son and friend were well impressed with the WORX, sadly for the makers they won'y be purchasing one as they'll be borrowing mine!
Very easy to use and I have found the cutting guide rail (included) to be very useful indeed. I'm lucky in that I can easily use it one handed but appreciate that someone with small hands may experience problems, as the handle is quite thick since it houses the motor. The included blade is brilliant, having said that, I have only used it for cutting wood of various thickness. Another caveat is the cutting depth which is about 26mm - all the decking I cut was 28mm thick, however the cut was deep and precise enough to simply snap the ends off. For some fence posts I simply rotated them and cut from the other side - easy.
My son and friend were well impressed with the WORX, sadly for the makers they won'y be purchasing one as they'll be borrowing mine!
Jason Raven
31.01.2023
10/10
Оценка пользователя
Великолепно
Brilliant saw for one handed accurate cutting!
I wanted a saw for long cuts and cross cuts. I have a sliding mitre saw but it is limited to 10" cuts, and I debated getting a full sized circular saw as they have more power, but in truth I don't need a big saw all the while, and I don't like the fact that unless they have soft start, bigger saws tend to do a sideways 'kick' as the motor starts.
I did lots of reviewing and product matching, and ended up getting this on a deal for £90....
The Result? This saw is easy to hold in one hand, and can cut through wood nice and straight thanks to the switchable laser on top.
Bottom line; this is a great saw that seems very capable, and not too big to make it scary or hard to handle.
Recommended!
I did lots of reviewing and product matching, and ended up getting this on a deal for £90....
The Result? This saw is easy to hold in one hand, and can cut through wood nice and straight thanks to the switchable laser on top.
Bottom line; this is a great saw that seems very capable, and not too big to make it scary or hard to handle.
Recommended!
C. Lozetsky
31.01.2023
10/10
Оценка пользователя
Великолепно
Easy to use especially for a novice
My carpenter mate has one of these so I decided to get one. First time ever using a power saw but after a bit of practice and much YouTube instructions, I am very happy with this saw. Have cut decking, made deck steps, shelving and cut a metal pipe with both straight cuts and 45 degree mitres. This is my first time buying 'proper tools' and I usually cannot knock a nail in straight. So pleased with this saw. Easy to use, portable and comes in a nice box for storage. Now looking for other projects to tackle.
CHARLES HOWES
31.01.2023
10/10
Оценка пользователя
Великолепно
Also comes with parallel guide and vacuum adapter
Simple to follow set up, easy to switch blade, accurate height adjustment. Good tool for the DIY’er
Mr. A. Popple
31.01.2023
8/10
Оценка пользователя
Хорошо
Worx for me.
I have only used the saw to cut 9 Ply Plywood up to now but found the cut to be 95% splinter free in all cut directions across the board. This could be down to it being a brand new blade and may worsen in time. There was enough power in the motor to breeze through the cut without any problem at all. The only minor problem for me is I cannot press the safety button with my thumb if I hold the saw in a comfortable sawing position. I am having to press the button in with my left hand and pull the trigger in the sawing position with my right hand. Not a problem at the moment because I tend to clamp everything I cut to the workbench but may not always be able to do this if I need to hold anything with my left hand while sawing. I would like the safety button to be housed just a little higher up for this reason but understand we are not all built the same.
Jim Spence
31.01.2023
6/10
Оценка пользователя
Плохо
Disappointed
It's a good strong saw but the guide could be locked in with a thumbturn instead of a caphead to make it easier and the the 0(zero) on the base for the cutting point is over 1mm out fro the blade making the cut out.
John 3 16
31.01.2023
8/10
Оценка пользователя
Хорошо
Great Saw, replacement blades are too expensive.
Really nice bit of kit, really glad I bought it, I have used it in a number of jobs since I bought it. The shape of the guide means that it can be ajusted to take off even the smallest amount. Very little kick on start up. Lazer a great help to give stright cuts, it is so easy to follow premarked lines. So why not 5 stars? Can't understand why it it was made with 46mm cut, as so much marerial is 50mm. I can only think it is so that other blades will not fit. The replacement blades are expensive and as I have been cutting mahogany the wood blade is already feeling blunt. I don't think everyone would want the 3 blades that come with it, but there is no choice. I hope cheaper replacements come on the market soon. The grip is quite wide and when doing a lot of cutting can be difficult to grip for someone with a small hand.
Mr G
31.01.2023
10/10
Оценка пользователя
Великолепно
Efficient tool
Not exactly a feather weight but lots better than a full size saw. It's a handy sized tool that gets the job done. Previous comments about its accuracy are a little unfair. I'll concede that the guide isn't properly square straight out of the box, but it doesn't take much to align it by bending the bracket a wee bit. However, if you clamp a piece of straight scrap timber to your work piece, the framework runs true when either using it for left or right hand cuts. So far I've had no problems whatsoever with this efficient little tool. I assume that it is aimed at the average DIYer and not for heavy duty professional use. I would recommend this to any skilled DIY tog. Always remember that this is a serious tool and not to be abused, ALAWAYS follow the safety instructions!
Amazon Customer
31.01.2023
6/10
Оценка пользователя
Плохо
First one was bent!
The first one I purchased had damage to the base plate, which was curled up at one corner and did not sit correctly on a flat surface. It was also impossible to adjust the saw so it didn't cut at 5 degrees. If I had to guess the saw had been dropped from height, so as to put all its component out of line. I also felt when I opened the box that it has previously been opened, despite having security tie on the catches! It was returned and a replacement received two day later which was excellent service from Amazon. I've given 3 Stars as not used the replacement yet but it is totally different to the first one, as everything appears to be in line and it has a flat base plate!
Lefty53
31.01.2023
8/10
Оценка пользователя
Хорошо
Good
Good mini saw, does get hot only used on chipboard 1", the laser is as much use as a chocolate fireguard impossible to see unless in low light, its only letdown.
keith tumbridge
31.01.2023
10/10
Оценка пользователя
Великолепно
Really pleased with it
It was perfect for what I needed it for
melvin
31.01.2023
10/10
Оценка пользователя
Великолепно
it's a learning curve to get decent performance.
when I first started using this saw I got OK cuts if you're not a professional, just a tiny bit off square. also even going thru something as basic as regularised 3''x2'' I wasn't making thru in one pass. the saw would kick up in the last few millimetres. keeping on the line you wanted wasn't easy either.
HOWEVER, at some point I doubled the effort I applied in pushing the saw downwards and stopped trying to advance forward in the cut. keeping the plate down is obvious but it's not always clear that you haven't got it touching everywhere. push down more, the kicking up stops, it goes thru in one pass and you finally get a precise cut with a clean face.
hope this helps someone out there.
HOWEVER, at some point I doubled the effort I applied in pushing the saw downwards and stopped trying to advance forward in the cut. keeping the plate down is obvious but it's not always clear that you haven't got it touching everywhere. push down more, the kicking up stops, it goes thru in one pass and you finally get a precise cut with a clean face.
hope this helps someone out there.
Stephen Gale
31.01.2023
8/10
Оценка пользователя
Хорошо
Good, but could be better
Using the the 710 watt version to cut laminate flooring..Not a bad machine and certainly more superior than a jigsaw when cutting laminate - very fast and no wander. When it works properly, the laser guide is a very useful feature indeed. However, it appears to be a bit of a mickey mouse add-on and you have to turn it on and off manually. It cannot be that difficult to integrate the laser power source into the machine can it?
If you're not used to this type of machine, you might find the ergonomics slightly odd. Personally, I would like to see a hand-grip at 90 degrees to the body - similar to an angle grinder, with the power switch built in, but that's probably me just getting used to the machine. Using it one-handed, I have found my fingers fouling the blade guard as it rotates, but i think i will get used to it. can only give 4 stars because of the unreliable laser.
If you're not used to this type of machine, you might find the ergonomics slightly odd. Personally, I would like to see a hand-grip at 90 degrees to the body - similar to an angle grinder, with the power switch built in, but that's probably me just getting used to the machine. Using it one-handed, I have found my fingers fouling the blade guard as it rotates, but i think i will get used to it. can only give 4 stars because of the unreliable laser.
Matty M
31.01.2023
8/10
Оценка пользователя
Хорошо
Love these little saws
This is the second one I've bought. I've marked it down for accuracy because the screw in fence thing it comes with is pretty poor and because the blade is small it doesn't keep itself on a straight line like a full size one might.
They are however really portable, make a nice cut, aren't stupidly loud and the dust extraction even works a bit.
I've built this second one into a pair of guide rails to make a mini track saw to cut sheet materials down on a vertical frame and it works perfectly.
They are however really portable, make a nice cut, aren't stupidly loud and the dust extraction even works a bit.
I've built this second one into a pair of guide rails to make a mini track saw to cut sheet materials down on a vertical frame and it works perfectly.
Paul Brimstone
31.01.2023
10/10
Оценка пользователя
Великолепно
Nice tool to use
It's a handy tool. I'm cutting 2 inch timber, which I do with two cuts. The laser is useful when plunging, to see the angle of the cut prior to sinking the cutting wheel. Nicer to use than a circular saw. Good for accuracy.
BT
31.01.2023
2/10
Оценка пользователя
Ужасно
Not fit for DIY, more a hobby saw.
Ok....I read the reviews before buying this and as always, read the bad reviews first. Ignored them and bought it anyway. There was my mistake.
Tried cutting a single sheet of corrugated tin and it kept jamming and didn't have the power just to cutting through the snags. Every time the teeth hit the edge and even a small amount of pressure was applied it just jammed and stopped spinning. Decided to give it the benefit of doubt and then went on to cutting some chipboard. Tried cutting a 20mm sheet of chipboard and it failed terribly. I had the blade depth set correctly and followed all of the instructions. Blade kept jamming in the cut and saw just stops. tried restarting the cut and going slowly, but all that happened is the saw started smoking and still kept stopping when the blade started cutting into the wood. After a couple of attempts, the blade was too warped under the heat to continue. I get that the blades that come with it are cheap, but the lack of power for a corded saw is awful.
If you want a cool hobby saw...its probably perfect. If you want a DIY tool that will tackle even basic materials at thicknesses of 20mm, this is not the saw for you.
If my problem was isolated I would assume I got a faulty device, but I am seeing a other reviews from people with exactly the same experience.
oh....and to cap it all off, the accuracy when cutting using the laser or the iron sight as a guide is a joke. Cut starts wondering off to the left despite the laser AND the iron sight both showing the straight line being followed.
Tried cutting a single sheet of corrugated tin and it kept jamming and didn't have the power just to cutting through the snags. Every time the teeth hit the edge and even a small amount of pressure was applied it just jammed and stopped spinning. Decided to give it the benefit of doubt and then went on to cutting some chipboard. Tried cutting a 20mm sheet of chipboard and it failed terribly. I had the blade depth set correctly and followed all of the instructions. Blade kept jamming in the cut and saw just stops. tried restarting the cut and going slowly, but all that happened is the saw started smoking and still kept stopping when the blade started cutting into the wood. After a couple of attempts, the blade was too warped under the heat to continue. I get that the blades that come with it are cheap, but the lack of power for a corded saw is awful.
If you want a cool hobby saw...its probably perfect. If you want a DIY tool that will tackle even basic materials at thicknesses of 20mm, this is not the saw for you.
If my problem was isolated I would assume I got a faulty device, but I am seeing a other reviews from people with exactly the same experience.
oh....and to cap it all off, the accuracy when cutting using the laser or the iron sight as a guide is a joke. Cut starts wondering off to the left despite the laser AND the iron sight both showing the straight line being followed.
C. J. Ward
31.01.2023
10/10
Оценка пользователя
Великолепно
Genuinely Compact and Light Weight
Before buying the Wrox, I bought a Mac Allister MSMCS500, which had a nice box and more blades, lower price too. However, it was far too heavy and clumsy, not really 'mini' and I needed to cut in a tight working space - especially important to keep a low profile.
The Wrox has proven perfect for the job, easy to handle, powers through floorboards, marine plywood, chipboard and the front end is relatively close to the blade, important in tight spots. Very happy with my purchase, worth the extra money.
The Wrox has proven perfect for the job, easy to handle, powers through floorboards, marine plywood, chipboard and the front end is relatively close to the blade, important in tight spots. Very happy with my purchase, worth the extra money.
onwheels
31.01.2023
8/10
Оценка пользователя
Хорошо
light easy to use single handed
only improvement would be to include additional fine cut blade
cuts through 18mm mdf with ease fast and straight used a saxton 60T blade not 24T supplied
cuts through 18mm mdf with ease fast and straight used a saxton 60T blade not 24T supplied
Amazon Customer
31.01.2023
8/10
Оценка пользователя
Хорошо
Good for price
Total DIY novice and not particularly dexterous so really all power tools are not really my forte , but I did find this light and quite easy to use any issues such as the blade getting stuck in the wood and any inaccuracies is all down to my developing skills .... basically if I’m happy with it , it must be decent
Mr S.
31.01.2023
8/10
Оценка пользователя
Хорошо
Worx ok.😎
Like the size of machine. Having done a few test cuts I found like some other reviewers the blade tended to wander. I replaced it with a generic one from Screwfix. This has a slightly wider kerf which so far seams to have solved the issue as cut through 18mm plywood ok. Since I have only done a few test cuts how it performs in the long term only time will tell.
Robert Dotchin
31.01.2023
6/10
Оценка пользователя
Плохо
It only lasts five days
The saw was good for five days, then it broke. So I sent it back, and I was refunded my money after three days.
Rskeats
31.01.2023
10/10
Оценка пользователя
Великолепно
WORX WX437 XL 800W cuts through wood quickly.
I brought this to cut lots of cut 10 - 12cm by 18 - 20mm pine wood to put behind desks where they'd be supported with brackets but doesn't have to be accurate.
I anticipate with a tool like this that the cuts are not going to be accurate and at my skillset of not using it much but it did exactly what I wanted it to do and I did manage to make some cuts straight without the bracket thing that comes with it that I found more of a burden.
I do feel a bit or resistance which influences my cutting of the wood where I'd end up getting the cut out of level significantly and this is the protective cover over the blade which the springs on there seems a bit tough. I don't think it would affect cutting large pieces when the cover is fully open.
I found that using the other hand to hold back the knob on the blade cover to fully open it before cutting solves that issue. It seems safe as one hand is holding the tool and the other hand is holding the knob back to keep the blade cover open where I can see where my hands are and that should prevent me accidentally putting my fingers near the blade during cutting.
There seems to be something lacking in the Amazon feedback system. When there are multiple products under one listing like this one for different types of saws and a reviewer of that listing leaves a review for one of them there is no mention of which product they are referring to unless they specify.
Despite selecting "WORX WX437 XL 800W" I have been seeing reviews for other models in the listing with problems which I didn't know at the time and I ended getting a lift to rush to Screwfix on Christmas eve to buy a third party compatible universal 85mm blade specified by reviewer for a different smaller saw in that listing under the impression that the tool I brought is good but the provided blade will give problems. I saw other reviewers confirming that the 85mm blade that comes with it wasn't any good where it would overheat, expand and start bending and one mentioning about it hitting the knife and cutting wrong and this 85m blade specified and pictures solved the issue for that reviewer.
It was arriving on Christmas eve and was preparing the 5mm blade for it and It was only when I looked at the blade on the model that I brought (WORX WX437 XL 800W) on a higher resolution picture that I coped into Irfanview then I see that it takes 115mm 120mm and not 85mm. I checked again and I realize they could be referring to three other 400w saws including the WX426 plunge cut.
I looked at the lower power model up which is the WX439 500W on Argus that uses the same 120mm blades and they have 4 to 5 star reviews: 68, (5 star reviews ) and 4 star (5 reviews) and no mention of the issues that the models that use the 85mm blade reportedly have.
I am pleased I made the right decision and went for the large extra power model as I was almost about the buy the smaller one.
Very misleading for reviews for a different product to be shown up not matching the one selected. I hope this issues gets fixed so when I select a product within a multilisting like this one only the relevant reviews relevant to that product are shown.
I anticipate with a tool like this that the cuts are not going to be accurate and at my skillset of not using it much but it did exactly what I wanted it to do and I did manage to make some cuts straight without the bracket thing that comes with it that I found more of a burden.
I do feel a bit or resistance which influences my cutting of the wood where I'd end up getting the cut out of level significantly and this is the protective cover over the blade which the springs on there seems a bit tough. I don't think it would affect cutting large pieces when the cover is fully open.
I found that using the other hand to hold back the knob on the blade cover to fully open it before cutting solves that issue. It seems safe as one hand is holding the tool and the other hand is holding the knob back to keep the blade cover open where I can see where my hands are and that should prevent me accidentally putting my fingers near the blade during cutting.
There seems to be something lacking in the Amazon feedback system. When there are multiple products under one listing like this one for different types of saws and a reviewer of that listing leaves a review for one of them there is no mention of which product they are referring to unless they specify.
Despite selecting "WORX WX437 XL 800W" I have been seeing reviews for other models in the listing with problems which I didn't know at the time and I ended getting a lift to rush to Screwfix on Christmas eve to buy a third party compatible universal 85mm blade specified by reviewer for a different smaller saw in that listing under the impression that the tool I brought is good but the provided blade will give problems. I saw other reviewers confirming that the 85mm blade that comes with it wasn't any good where it would overheat, expand and start bending and one mentioning about it hitting the knife and cutting wrong and this 85m blade specified and pictures solved the issue for that reviewer.
It was arriving on Christmas eve and was preparing the 5mm blade for it and It was only when I looked at the blade on the model that I brought (WORX WX437 XL 800W) on a higher resolution picture that I coped into Irfanview then I see that it takes 115mm 120mm and not 85mm. I checked again and I realize they could be referring to three other 400w saws including the WX426 plunge cut.
I looked at the lower power model up which is the WX439 500W on Argus that uses the same 120mm blades and they have 4 to 5 star reviews: 68, (5 star reviews ) and 4 star (5 reviews) and no mention of the issues that the models that use the 85mm blade reportedly have.
I am pleased I made the right decision and went for the large extra power model as I was almost about the buy the smaller one.
Very misleading for reviews for a different product to be shown up not matching the one selected. I hope this issues gets fixed so when I select a product within a multilisting like this one only the relevant reviews relevant to that product are shown.
CeeJay
31.01.2023
4/10
Оценка пользователя
Ужасно
Good addition any toolbox
Nice piece of kit. Seems to be well made and robust. OK it's not anything like as powerful as a full on 7" (or bigger) circular saw, but it is ideal for simple cuts on thinner sheet timber that is so often the type of use I had in mind when I bought this tool. Lighter weight than its big brothers, it is easy to use and pretty accurate. Overall I feel it is well worth the cost.
Amazon Customer
31.01.2023
8/10
Оценка пользователя
Хорошо
Review for the Worx WX427 710 W
To be honest after reading the many reviews on this item I wasn't convinced it was going to be the right tool for me there were so many reviews reporting the same problem with the cut not staying true and straight. So I decided to do some research by going to smaller shops who sell building/everyday tools with the intention of getting advise from a professional. It just so happened that this guy didn't sell Worx but has owned them and he couldn't praise the tool enough so I went ahead and purchased and as promised was delivered the next day. I was kinda excited to open the box as I needed to complete this job before the Christmas break. The tool is surprisingly big to what I was expecting but not cumbersome if your getting my drift in fact it's light and easy to control which is big plus in my book but now for the disappointment I needed a saw that would cut 30cm + so this model should be perfect right? it's advertised that's its capable of cutting up to 46cm! wrong!! I'm cutting through 20cm and after 400cm it's cutting off line. now I'm starting to wonder if I've made the wrong purchase after all you spend a lot of money on a tool and it doesn't quite live up to what you expect so with a cuppa in hand I start to work out what the heck's going wrong after all its new out of the box! ... and then it suddenly hits me I pick up the tool and I look at the blade and I'm looking and looking and I start to realise the blade is just to thin!! as the blade cuts its getting hot and the heat causes the blade to distort hence it cuts out of line. In my opinion its a design flaw the blade needs to be thicker or a better quality metal????... The laser is a handy item to have but on my tool the laser is to wide and you cant see my guide line it needs to be a pencil line. But apart from the problems I've experienced the tool has a powerful quiet motor and with the blade sorted will make an awesome tool in any bodies workshop. I would like to get in contact with Worx customer services and see what they have to say about this fault I don't understand how they can test these tools themselves and not get the same results as most of us are getting.
I hope my review helps and happy shopping and stay safe..
Simon
I hope my review helps and happy shopping and stay safe..
Simon
A. Butler
31.01.2023
10/10
Оценка пользователя
Великолепно
says it in the name - it just Worx!
Worx - does like the name says. It just worx
I got this for cutting wood mostly though I may use it for other materials as well. On the day I ordered this, there was a special offer on a much more powerful model too. I went for this as it would fit in one hand and had the depth of cut and more I required.
I have one of those xactsaws too, that is a clumsy, hard to use saw in comparison to this. Where the xact is difficult to turn on and the spring around the blade guard is far too strong, I found this very easy indeed. I really can be used one-handed.
I found the depth of cut adjustment to be easy and the size guide that comes with the saw works very well indeed, though my own clumsiness did mean I lost the holder screw for it for a while (now found again).
If there was one change I'd make to this saw it would be a tool box to hold it in as the box will quickly become scruffy and damaged, other than the saw really is a great device.
I got this for cutting wood mostly though I may use it for other materials as well. On the day I ordered this, there was a special offer on a much more powerful model too. I went for this as it would fit in one hand and had the depth of cut and more I required.
I have one of those xactsaws too, that is a clumsy, hard to use saw in comparison to this. Where the xact is difficult to turn on and the spring around the blade guard is far too strong, I found this very easy indeed. I really can be used one-handed.
I found the depth of cut adjustment to be easy and the size guide that comes with the saw works very well indeed, though my own clumsiness did mean I lost the holder screw for it for a while (now found again).
If there was one change I'd make to this saw it would be a tool box to hold it in as the box will quickly become scruffy and damaged, other than the saw really is a great device.
Kindle Customer
31.01.2023
10/10
Оценка пользователя
Великолепно
Expensive but really useful
Expensive but of kit in initial layout of funds but really useful when you don’t want to drag out a large circular saw. A bit on the heavy side. Given the choice again I wouldn’t have bothered with the laser sight and saved some money. On the whole would recommend
fantompoet
31.01.2023
10/10
Оценка пользователя
Великолепно
Why did I not buy one of these sooner
Lovely piece of kit and very useful. I had borrowed a similar Worx unit from a friend and was smitten so got myself one. My only gripe with this model is that the laser is battery powered and not powered from the unit itself, it's a small gripe as I love this thing. It's very accurate and cuts cleanly, what more can you ask of it...
Wai Tung Ho
31.01.2023
8/10
Оценка пользователя
Хорошо
The motor actually got really hot due to poor technique. The cut has a tendency to drift ...
This is a little beast of a saw.
I used it to cut up 9 sheets of inch thick plywood that were 8 x 4 and weighed 45kg each so there was no way I was getting them onto my bench saw.
It's hard to keep the cut going straight and perpendicular to the surface, but it did well enough. The ability to vary the depth of the cut was the crucial to this task as I was cutting it resting on top of other plywood sheets below it.
I then used it to cut out the borders on my parquet floor in a 22m2 room, the real reason why I purchased this. This was much trickier and required a certain technique. The motor actually got really hot due to poor technique. The cut has a tendency to drift either left or right or at an angle and this puts extra strain on the saw which causes it to heat up.
To combat this, the saw needs to be lifted up, the alignment altered to the direction of the cut before being lowered again, in effect cutting out a new groove in the direction you want to go, before continuing.
It also needs to have a vacuum attached otherwise the dust that is created will clog the saw up and may cause it to catch fire. Think of Ray Mears and his friction fire lighting demo, except using a 700W powertool instead of a hand driven stick.
There's no doubt that a lot of care needs to be taken when using this. Inattention and poor technique can easily result in very serious injury. I've had it jump back at me unexpectedly a number of times, so be careful!
It needs a firm and purposeful hand but used correctly and it will do the job asked of it.
However, if I didn't need to vary the depth, I would probably have been better served with an ordinary hand-held circular saw.
Also the laser guide is sometimes not that accurate and becomes offset from the line.
I used it to cut up 9 sheets of inch thick plywood that were 8 x 4 and weighed 45kg each so there was no way I was getting them onto my bench saw.
It's hard to keep the cut going straight and perpendicular to the surface, but it did well enough. The ability to vary the depth of the cut was the crucial to this task as I was cutting it resting on top of other plywood sheets below it.
I then used it to cut out the borders on my parquet floor in a 22m2 room, the real reason why I purchased this. This was much trickier and required a certain technique. The motor actually got really hot due to poor technique. The cut has a tendency to drift either left or right or at an angle and this puts extra strain on the saw which causes it to heat up.
To combat this, the saw needs to be lifted up, the alignment altered to the direction of the cut before being lowered again, in effect cutting out a new groove in the direction you want to go, before continuing.
It also needs to have a vacuum attached otherwise the dust that is created will clog the saw up and may cause it to catch fire. Think of Ray Mears and his friction fire lighting demo, except using a 700W powertool instead of a hand driven stick.
There's no doubt that a lot of care needs to be taken when using this. Inattention and poor technique can easily result in very serious injury. I've had it jump back at me unexpectedly a number of times, so be careful!
It needs a firm and purposeful hand but used correctly and it will do the job asked of it.
However, if I didn't need to vary the depth, I would probably have been better served with an ordinary hand-held circular saw.
Also the laser guide is sometimes not that accurate and becomes offset from the line.
KJ Foxwell
31.01.2023
8/10
Оценка пользователя
Хорошо
Small compact powerful
Very good
David James
31.01.2023
10/10
Оценка пользователя
Великолепно
Works well
Great product
Bob
31.01.2023
6/10
Оценка пользователя
Плохо
Does what it says
Does what you want from it & a bloody miracle that it works as it came from Amazon.
2 out of 4 electrical items purchased were faulty.
2 out of 4 electrical items purchased were faulty.
norman edwards
31.01.2023
10/10
Оценка пользователя
Великолепно
Punching well above it's weight
Not sure what I was expecting, but this exceed's it , for the price it is excellent value, for the average d.i.y.'er
Stevie boy
31.01.2023
10/10
Оценка пользователя
Великолепно
A good item
Just the thing to cut through small pieces of wood good make also easy to use would recommend this product
Patrick
31.01.2023
10/10
Оценка пользователя
Великолепно
Great little saw.
When looking for a "one job" small saw I happened upon this and reading the reviews (where many were saying it wouldn't cut a straight line) I almost went elsewhere. But for the price I took a chance and I'm glad I did.
It just goes to show that you really should ignore most Amazon reviews, ironic i know.
The two pics included show that this saw cuts perfectly fine and straight, I'm pretty unfit and was stooped over cutting this practically free hand so I don't know why other users are having trouble. I've come to the conclusion they may have had the wrong blade in, the blade in backwards or they just don't know how to use power tools.
For just under €100 this is a great addition to the tool chest. The job in the pictures is a 12mm deep cut approx 8 metres long and I couldn't have hoped for any better. I am tiling the bathroom soon and have no doubt this saw will cut tiles just as well, (with the correct blade).
The vacuum attachment doesn't fit the henry hoover very well, or at all in fact, so I assume most vacuums. but no matter what cutting job you have to do, you'll vacuum afterwards anyway so it's not an issue for me.
It just goes to show that you really should ignore most Amazon reviews, ironic i know.
The two pics included show that this saw cuts perfectly fine and straight, I'm pretty unfit and was stooped over cutting this practically free hand so I don't know why other users are having trouble. I've come to the conclusion they may have had the wrong blade in, the blade in backwards or they just don't know how to use power tools.
For just under €100 this is a great addition to the tool chest. The job in the pictures is a 12mm deep cut approx 8 metres long and I couldn't have hoped for any better. I am tiling the bathroom soon and have no doubt this saw will cut tiles just as well, (with the correct blade).
The vacuum attachment doesn't fit the henry hoover very well, or at all in fact, so I assume most vacuums. but no matter what cutting job you have to do, you'll vacuum afterwards anyway so it's not an issue for me.
stephen hill
31.01.2023
10/10
Оценка пользователя
Великолепно
Not a good experience
After using initially it cut very accurate and clean, but after a few uses it got stuck in some wood and the gears sheared off making it unusable. Would have been nice for the price to have an auto cut off mechanism for this kind of problem.
Ed (carpenter, general builder)
31.01.2023
10/10
Оценка пользователя
Великолепно
High power, quality, deep cutting saw
Amazing tool. Primarily purchased to cut down doors. I'm a carpenter and wanted to replace a large skill saw with a small easier to use saw. I chose the worx saw as the motor is 300W more powerful than the competitions but mostly because it cuts up to 45mm deep others only go to 28mm deep which won't go throw and internal door of 33mm this beautiful tool fly's through 45mm which is an external or fire door thickness like a dream. I have many Powertools this one is an awesome addition.
I did not think it came with a guide but it does. Easy to use and cuts very cleanly, easy to operate with one hand. High quality tool, good case.
Only thing that I think would be an improvement, and this is a tiny niggle, I'm being very critical now, is you have to squeeze up an Allen key nut to lock the guide -supplied and stores at the end if the handle. Although if they put a wing nut on it, it would be bigger and get in the way. So they have done the right thing.
I would happily recommend this to all, worth every penny and looks to me like it will last many years. I could not be happier.
Delivery reliably speedy as always.
I did not think it came with a guide but it does. Easy to use and cuts very cleanly, easy to operate with one hand. High quality tool, good case.
Only thing that I think would be an improvement, and this is a tiny niggle, I'm being very critical now, is you have to squeeze up an Allen key nut to lock the guide -supplied and stores at the end if the handle. Although if they put a wing nut on it, it would be bigger and get in the way. So they have done the right thing.
I would happily recommend this to all, worth every penny and looks to me like it will last many years. I could not be happier.
Delivery reliably speedy as always.
rohit
31.01.2023
8/10
Оценка пользователя
Хорошо
Good Saw
Ordered it for little diy for my garden and this is good saw for small and med size projects.
Miss M A Gilpin
31.01.2023
10/10
Оценка пользователя
Великолепно
Great little saw
I am a novice at woodwork, but I am having a go. I have used it several times now to cut wood and I am pleased with the results sj far.
Tony Roberts
31.01.2023
8/10
Оценка пользователя
Хорошо
Good feel to the tool and good value.
Bought initially for cutting mdf and chipboard sheets to avoid hand cutting. The first cut made in 9mm mdf showed up the need to set the depth of cut appropriately. It was also not easy to follow a pencil line as there was a tendency to drift to one side. Using a clamped on batten, some inch or so from the desired cut line, the saw performed well with a smooth and accurate cut resulting. Power is adequate for mdf and chipboard up to 12mm but it struggles with thicker boards. Once the feel of the tool has been got used to it is comfortable to use. Quality of build and ease of adjustment is good as is value for money.
Mr. David Robinson
31.01.2023
10/10
Оценка пользователя
Великолепно
great piece of kit.
I own the first incarnation of this tool which fits a 78mm blade, I use it for rebating and grooving and cutting sheet material. it is limited by it's depth of cut of 28mm ish I love it despite its limitations. So I bought it's big brother mainly to cut deeper for example ..decking boards... but I also bought the tougher blade for its 1.8mm kerf. This has allowed me to cut perfect channels for weather stripping and refurbishing 20 sash windows (2.0mm is recommended but I knew from previous attempts 1.8 would do.) If you have ever fiddled about with a router trying to do this job you will know it can be a nightmare on site with limited workspace...this little beauty zipped through the job without a single wobble, also trimmed doors, channeled out for intumescent stripping. The saw has plenty of chuff and can cut its way through a fire door.. provided you can allow it to take it's time and not push it. It is a bit heavier than the 400 watt version but I have both now....a great flexible site tool.
Показаны отзывы 9-56 из 154.
Альтернативы с более высокой оценкой
Wizemart © 2026.
Рекомендательная система по умному выбору товаров по отзывам и рейтингам
