Отзывы о Поверхностный насос Grundfos JP 5-48 (1490 Вт)
379 отзывов пользователей o Grundfos JP 5-48 (1490 Вт)
Пользовались
Grundfos JP 5-48 (1490 Вт)?
Поделитесь своим опытом и помогите другим сделать правильный выбор
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Grundfos-это здорово
очень хороший пункт...так приятно иметь постоянное давление в моем доме сейчас. Я бы рекомендовал этот пункт для всех моих друзей
Скроменый эксперт
4/10
Оценка пользователя
Ужасно
Шесть лет и провал
Думал, что я покупал 15-20 лет решения, но получил только шесть лет и провал ..... Черт это все ..... Иногда вы просто не можете выиграть!
Скроменый эксперт
4/10
Оценка пользователя
Ужасно
Дитто. не покупайте
5 ч 9 месяцев отличный напор воды. Силовой модуль управления плохо. 5-летняя гарантия. Здорово. Не покупайте в этой системе.
Скроменый эксперт
4/10
Оценка пользователя
Ужасно
Во избежание этой модели..
Хорошо работал в течение 14 месяцев.. не бросил .. заменить старые модели. Надеюсь, дольше. Во Избежание Скала 2..
Скроменый эксперт
8/10
Оценка пользователя
Хорошо
Хороший продукт, медленная доставка
Продукт был отличным. Говорит, два дня доставка, и я не получить его до 5 дней (конечно же рассчитывает на что).
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Наш стандарт
Мы используем их, чтобы вода течет ежедневно. Они хорошо работают и держат.
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Обслуживание клиентов высшего качества
Качественный продукт по разумной цене. Отличное обслуживание клиентов!
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Удивительный продукт
Простота установки и очень тихо. Я хотел бы купить еще раз.
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Это делает работу
товар был доставлен и работает как рекламируется
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Контроль Давления Грундфос
Отличный Продукт
Скроменый эксперт
10/10
Оценка пользователя
Великолепно
Пять Звезд
Работал отлично
yvonne
05.01.2021
6/10
Оценка пользователя
Плохо
probably it's fine
but we cant figure out why it stopped working. Does it need to be positioned a certain way? (as in for venting holes or something? - we ensured it is horizontal, but is there something more - is that square controller thing shown on the graphic above to be sideways OK to be down? Secondly, Is it a problem that we took out the previous model and mated the grundfos to the other larger size pipes. - it worked, then it stopped, then it worked, then it stopped. Right now the old pump is back in.
Jason Jackson
05.01.2021
10/10
Оценка пользователя
Великолепно
Grundfos for the win!
Our older circ pump went out and I needed to replace it. This pump is AWESOME! Super easy to wire, and it came with the mounting plate as well. It feels like it puts out a little more flow than our old 115 vac model, but that could be because it's new and working correctly. All in all, perfect replacement! removed the old unit, crimped two new ends on the new one and away we went. Total time for replacement was under 10 minutes.
Rich D
05.01.2021
6/10
Оценка пользователя
Плохо
Not Sure..
It seemed to be runnin hot when I first got my tub turned on.
It ran though.. for a couple weeks. I'm not sure if it was defective or not.
I just shorted out (self destructed).
It ran though.. for a couple weeks. I'm not sure if it was defective or not.
I just shorted out (self destructed).
Larry Moran
05.01.2021
2/10
Оценка пользователя
Ужасно
One Star
Only lasted 6 months.
Leonard Goduto
05.01.2021
8/10
Оценка пользователя
Хорошо
This is the second one. The first one lasted ...
This is the second one . The first one lasted about two years. Should get five years out of it. Hopefully this one will last.
T.V.
05.01.2021
8/10
Оценка пользователя
Хорошо
It Works
not much to say About a pump, but I bought it a month ago and its still working just fine
baller
05.01.2021
10/10
Оценка пользователя
Великолепно
Five Stars
Excellent product fast delivery
Charles Wilson
05.01.2021
10/10
Оценка пользователя
Великолепно
Perfect Fit
This was a perfect fit for my hot tub. It has been working as it should. Simple to install an get running. Larry
Paul Sawyer
06.01.2021
10/10
Оценка пользователя
Великолепно
Come with both halves of the unions
I ordered this in September 2019. The product as pictured shows only half of the 1.25 inch unions and the rubber seals that go inside the unions. I just wanted to report that the pump did come with other half of the unions. So with the unions installed on the pump, you are left with 3/4 inch female NPT connections in brass. Contrary to the description, fittings to adapt to 1/2 inch or Sweat were not included. However adapters to do that can be found at any plumbing store or Home Depot. The Unions themselves are not something you would find at Home Depot. I don't know if plumbing stores carry them. Thankfully, both halves of the unions came with the pump.
So far I am very happy with the pump. I'm using it to circulate hot water from my hot water heater through a radiator to heat a room and back to the hot water heater. I originally built the system with a cheaper pump from a different manufacture however that pump failed after only a few years. With the original system, the pump was not run six months out of the year. That probably allowed mineral deposits to clog the pump. So with this pump, I plan to run it on a timer a few minutes every day even in the warm weather.
This pump is a "cartridge" style pump. The windings are fixed and apply magnetic fields through a thin stainless steel housing which serves as the water tight seal to the permanent magnet rotor assembly. The advantages of this design is that there isn't a shaft protruding through a water tight seal which would eventually wear out. Also water is in contact with everything that moves so it both lubricates and cools the moving parts.
So far I am very happy with the pump. I'm using it to circulate hot water from my hot water heater through a radiator to heat a room and back to the hot water heater. I originally built the system with a cheaper pump from a different manufacture however that pump failed after only a few years. With the original system, the pump was not run six months out of the year. That probably allowed mineral deposits to clog the pump. So with this pump, I plan to run it on a timer a few minutes every day even in the warm weather.
This pump is a "cartridge" style pump. The windings are fixed and apply magnetic fields through a thin stainless steel housing which serves as the water tight seal to the permanent magnet rotor assembly. The advantages of this design is that there isn't a shaft protruding through a water tight seal which would eventually wear out. Also water is in contact with everything that moves so it both lubricates and cools the moving parts.
Franz Metcalf
06.01.2021
10/10
Оценка пользователя
Великолепно
Seeming Exact Replacement for 59896127
Yes, this seems to be an exact replacement and is working fine in my house without changing anything but the rubber washers. Just shut off the water using a hex wrench on the tiny valves built into both ends of the fittings for the pump, take the old one out, replace the washers, chunk the new one in there and tighten the fittings.
You'll need to wire the new pump. I just used my old wiring, the green wire to ground, the two white wires to L and N. (In my case, since I had two white wires, I had to trace them back to the plug to learn which was connected to the narrow [=L] prong of the plug and which to the wide [=N] prong.)
Note: my pump was NOT labelled 59896775. It has another model number written on it, despite it being described as part 59896775 by Amazon. I called Grundfos and was told the differing number was due to it coming with the fittings as a kit. I find that hard to believe, but I can confirm the pump is working properly.
Oh, and finally, bleed air from the pump by using a very wide flathead screwdriver to loosen (not remove) the metal cap in the center of the front of the pump. Water will leak out. When it does and no bubbles are coming out, you should be good to go.
You'll need to wire the new pump. I just used my old wiring, the green wire to ground, the two white wires to L and N. (In my case, since I had two white wires, I had to trace them back to the plug to learn which was connected to the narrow [=L] prong of the plug and which to the wide [=N] prong.)
Note: my pump was NOT labelled 59896775. It has another model number written on it, despite it being described as part 59896775 by Amazon. I called Grundfos and was told the differing number was due to it coming with the fittings as a kit. I find that hard to believe, but I can confirm the pump is working properly.
Oh, and finally, bleed air from the pump by using a very wide flathead screwdriver to loosen (not remove) the metal cap in the center of the front of the pump. Water will leak out. When it does and no bubbles are coming out, you should be good to go.
Gregory S. Burns
06.01.2021
10/10
Оценка пользователя
Великолепно
Good news (...and good news)
The good news is that this is a high quality pump (Grundfos PN 59896775) that recirculates a home hot-water system perfectly. It replaces the Grundfos PN 59896127 pump perfectly (size, etc., the one I had previously and now discontinued) as advertised in the Grundfos technical data (middling-easy/hard to find that on-line). If, like me, you get part-way through the installation/replacement and find that, "Wow, the wiring is different" (as shown on page 8 of the installation manual that accompanies the pump) - no worries! Turns out that what appears to be a single-speed versus multi-speed wiring incompatibility is simply lousy instructions and illustrations in the installation manual. If you're replacing a 59896127 pump just take the two hot wires and connect them to the "L" and "N" connections, and connect the (most likely) green-colored ground wire to the terminal marked with the ground symbol. Too bad the Grundfos manual doesn't make it clear that you can connect a straight 115v/60c line input to the apparent multi-speed terminals on the new pump (as shown in their manual). I confirmed this via their (hard to find and relatively unpublished) customer service number (800-333-1366). Good luck googling any of this info (PITA - I had to pummel through it through several days of emails with the seller the hard way).
Oh, and while you're at it, once you have it installed and have turned the water back on after making all connections, and thereafter starting the pump, be sure to turn the central nickel-plated screw in the central shaft area to a loosened position to purge any air from the pump while it's running. DON'T remove the screw, just loosen it while the pump is running and let any air (and a little bit of water which will dribble out) escape. Once you have only water slightly escaping from that area retighten the screw and everything's Jake! This is easier to google (found it on another seller's website).
The pump may sound a little noisy at first, but after the ceramic bearings have seated in the first minute or so and after you've purged the air in the pump (described in preceding paragraph) the noise should go away and it should be relatively silent. Very nice.
Oh, and while you're at it, once you have it installed and have turned the water back on after making all connections, and thereafter starting the pump, be sure to turn the central nickel-plated screw in the central shaft area to a loosened position to purge any air from the pump while it's running. DON'T remove the screw, just loosen it while the pump is running and let any air (and a little bit of water which will dribble out) escape. Once you have only water slightly escaping from that area retighten the screw and everything's Jake! This is easier to google (found it on another seller's website).
The pump may sound a little noisy at first, but after the ceramic bearings have seated in the first minute or so and after you've purged the air in the pump (described in preceding paragraph) the noise should go away and it should be relatively silent. Very nice.
Whitewater Maintenance Corp.
06.01.2021
4/10
Оценка пользователя
Ужасно
Noisier than the original, or other models
I purchased this unit from this seller, because they had the best deal. It was super easy to install, everything but the power cable was included. The only issue is, even though it is a drop in replacement, the unit itself if pretty noisy. It is not in your face noisy, but that running noise travels down the pipes and when it is quiet and not much us going on, you can clearly hear the pump running, even 50 ft away from the pump. The seller was very nice, communicated well, and accepted my return without issue. Seller is great, the product however is not. A neighbor whose house was just built as a Grundfos pump on her home, probably a slightly different model. Her unit was as or more quiet than my 20 year old unit that failed. I was going to buy it again from another seller, hoping it was a one off problem, but now that I am reading the other reviews, I see it is a noisy pump. Back to the drawing board.
Arch Hughes
06.01.2021
6/10
Оценка пользователя
Плохо
Expensive and Noisy
So far this little pump is way more noisy than the 25 year old pump that I replaced with this one. I called the seller and got the exact replacement for my old pump. Removal of the old pump was a PITA because of the 25 years it had been collecting calcium. Once I removed it and cleaned the fittings, the new one fit in easily enough.
Показаны отзывы 169-192 из 379.
