Отзывы о Корпус Thermaltake The Tower 600 (CA-1Z1-00M6WN-00)

 I'm absolutely in love with this case and for the low price it's a steal. Especially with the tempered glass. It's truly one of a kind and will display your goods in style.

This thing is soo sturdy, albeit heavy. The bolts on the glass are plenty strong to keep this thing suspended under my table I built it into.

The options for placement and being able to vertically display a GPU are great. I have had no issues with the PCI-e riser included for my MSI GTX-1080. I wound up buying a second PCI riser for my wifi card.

Cons
- Instruction manual doesn't cover much for assembly. I had a really hard time figuring out which of the 10 screw varieties were the right one to attach each piece (had to trial and error).
- I wish there was some kind of L bracket or something to mount my 5 old noctua fans for more airflow around the outside of the case. Thermals are 2-4ish degrees better than in my corsair spec-01 enclosed case.
- i wish the back cover wasn't a crappy metal slide in style which 1 notch always gets missed. Can't complain though since they would have had to raise the price otherwise.

What I learned assembling it
- install GPU prior to PCU if mounting with the riser. Use thumb tighten screws for all 4 GPU bracket connection points.
- remove the heavy wall mount plate on the inside before anything else. Helps bring the weight down if you don't plan on wall mounting it.
- attach the big feet and small rubber ones so you can rotate it while installing.

I am an IT guy and love to build my own computers. It took me forever to figure out how to handle the PCI cards because they have 3 different configurations, one for ATX, mini-ATX, and some other one. Instructions were extremely poor. Looking online is no help.

Also, what made matters worse, I lost 1 hour because the motherboard to case screws were not the right size. Fortunately, these are standard female screws. I moved those screwed from my old PC. I dont know how they produced it with bad threading.

Really painful to put together. Took me 4-8 hours, what should have taken 1 hour. Nice once complete. But I would not do it again. Not worth my time.

Pros:
- fantastic cable management area
- plenty of space to work around
- solid vertical gpu mount
- room/hardware for open loop cooling
- can mount a 240mm radiator
- looks PHENOMENAL with Good components
- very sturdy and well built

Cons:
- comes with thermaltake's cheap pci extension cable
- only has 1 2.5" ssd and 3.5" hard drive mount, unless you don't use the radiator
- metal bracket inside the case is completely pointless
- the motherboard spacer screws are really jenky and don't leave much room behind the mobo for cable routing
- the case is very large and heavy for a mini itx build
- the radiator mount width is only 122.5mm wide, so you can't mount a 280mm radiator and certain radiators, like the nzxt kraken x52 and corsair h100I v2, will not fit
- it doesn't come with wall mounting hardware
- the assembly instructions are absolutely horrendous; it boggles me that a company would make such a great case and hand out instructions seemingly written by a 5 year old

All in all, if you want a great looking mini case then this is the best you'll get, but if you want a mini mini case then get something like the corsair v1.

I am an unconditional Lian Li user so the price tag of this case didn't shock me too much but I understand this can be a bit expensive for a case. For the first time in 18 years I bought a non Lian Li case because this Thermaltake's original shape really inspired me for a mod. The case is really heavy so that's a good sign. But it's also steel and plastic which does not really match a Lian Li's anodized aluminum and where you can hardly find plastic at all, TT case is mostly steel with some really nice and heavy glass side panels. The parts on the side that mimic the air intakes are plastic sadly as well as the cockpit on the front. Not so good. On the other hand, the case is huge with tons of room for large radiators, pumps and reservoirs. It's an open case so there will be some noise from the fans and pumps necessarily. I am expecting also that dust will collect a bit faster inside. What really impressed me with this case is how easy you can take it apart. Almost nothing is riveted and a simple screwdriver will allow you to individually mod and repaint each separated element without effort. That a very good point for modding. A small nuance I need to add is that the manufacturing precision is not yet there. Some parts need a bit of twisting for the holes to align so we are not really talking sub millimetric quality manufacturing here which, for this price, we should be entitled too.

This chassis is wonderful to work with.

Some reviews mentioned hard drive placement. I would say that if your going to use more then an M.2, look toward the larger p3 or p5. The internal space does have room for two hard drives inside, but this is precious space when it comes to cable routing. I removed both cages because I was using an M.2 and didn't need the storage. So I had tons of room in the case for cable management.

And cable management is a mixed bag. Not a negative. Just make sure you plan a lot! Pre-run every cable. Unlike most cases, there isn't a ton of holes to pass cable through, so you have to really think about where things should go. Take your time, and it will be fine. Keep your peripherals to a minimum, and you should be good.

I mounted a Kraken x52 on the right side mounting plate. According to previous reviews and information, the space here is limited so I grabbed the x52 instead of the x62. Trying to squeeze the radiator into the recess would have been tight, but I elected to mount the stock fans to the rear plate, pushing the rad out beyond the recess, then mounted some TT HD120's on the front, for a push pull (exhausting back as there is nice grill opening for just such a setup). It makes it nicer, and eliminates the issues others were having with mounting the rad. My thoughts on that are; you're buying an open air platform, put shiny fans on, and use the stock ones for the heavy lifting.

The only word of caution I would have is Power supply cables. If you are thinking about some aftermarket parts, I would say go for it. They tend to be more flexible, and that flexibility will come in handy when trying to route your ATX power connector behind the board. If you are using stock connectors, then I would highly advise pre-flexing the cable either way.

Last and most important. Take your time! It pays off in the end.

This case is pretty unique, so you'd think that the instructions would be really good, and they are some of the worst instructions ever. They really don't do a good job of telling you what to do step-by-step, some of the instructions are in really small print. The best part of the instructions was a single picture showing how all the pieces fit together, but it doesn't tell you which screws or specific pieces -- and it's about as useful as just looking at a picture of a completed case and guessing where everything goes. So it's basically useless. It's also very heavy, making moving around the computer very tedious.

On the other hand, it looks nice, has a simple glass look, and is very sturdy. Most of the people buying this are just buying for the looks, but the instructions are very poor, and it is very heavy. I think this case is not meant for beginners.

As the title states, if you like puzzle games this case is for you. The scant instructions in front smaller than you expect will guide you haphazardly through the construction of a case that should be easy.

Pros:

1. Amazing look
2. Solid construction
3. Red color is a great match to my msi board accents

Cons:

1. Where does the Power supply actually go? I mean you can guess 1 of like 4 places. I got it right on the 3rd try

2. If you opt to use the VGA tray, mount the card holder thing before you put the tray on. It doesn't make that very clear, but if you think in terms of puzzle games it is likely to be obvious

3. Expecting to be able to wall mount because the description says wall mountable? Yea, but only if you spend more money to get a special bracket which also isn't clear.

Overall it is an awesome case, but is very much geared to those with liquid cooling and SSD drives.

This is case is larger but otherwise quite similar in design to the smallest Core P3 and (now) intermediate-sized P5. However, there are some significant differences, most of which could be considered refinements. For instance, beneath the glass on the top and bottom panels there are now steel panels for fan or radiator mounting and the front panel has been modernized to include a single USB type C port along with additional USB type A ports and audio jacks.

The tempered glass panels have been pared down slightly to 4mm thickness from the 5mm of the previous models. They still feel substantial though personally I would have preferred thicker panels for an even greater perception of robust build quality.

The case comes fully assembled and I'm astonished that it arrived intact. Though I purchased it new direct from Thermaltake, the package had the look of an Amazon warehouse item that had already been shipped a few times. It was beaten up pretty badly, appeared to have been re-taped and was partially crushed in on one side. There's a single piece of styrofoam covering each end but otherwise that's it - no other padding or packaging for the other sides. That's the way traditional cases are usually packaged, but there's a lot of glass here.

Still, as bad as the box looked, no glass panes were cracked or shattered. That, despite the notoriously rough-handling folks at UPS having apparently ignored the "fragile" warning on the box, unless Thermaltake shipped it out in such poor condition which I suppose is possible...?

As with the other two models, Thermaltake advertises this as an open case but here the rest of the glass panels needed to "close" the case into a more traditional box come standard. There are still plenty of gaps and spaces, however, and I'm not yet sure exactly how dust will play into the equation over time. Hopefully, proper fan configuration - notably positive pressure, should help mitigate dust accumulation problems.

I'm keeping this build to a minimum so at least with my configuration noise isn't a factor at all - even with the main side panel off. You may want to keep the gaps and spaces in mind though if you're planning to put noisy components into the chassis.

The side with the most open space by far is the rear panel. It seems more refined than the predecessor models though it still doesn't have the same completely finished look of a more traditional chassis. This seems like an intentional design decision on the part of Thermaltake in order to maximize configuration options.

Keep in mind though that if you must have a traditional finished look to the rear of your case, you might have some issues here. The motherboard and power supply mount recessed by about 1 to 2 inches. Of course, functionally, that really doesn't seem to be a problem. Be aware that if you have an older motherboard like I do with a standard I/O shield that would normally wedge between the ports on the motherboard and a normal ATX case, it simply won't work here. You'll have to leave the I/O shield off. No big deal, really.

The back cable management and hard drive mounting area seems well designed with plenty of depth in the compartment. Three plates are included for mounting drives and you can put a single 3.5" or two 2.5" drives on each one. Mounting points exist for a couple more drive plates (sold separately). The removable VESA mounting block is nevertheless rigid and should provide a solid foundation if you choose to wall or TV mount the case.

There are a total of three dust filters included - one each for the top and bottom which are interchangeable but a little wider than the third filter that can either be placed at the front of the case or over the perforated opening on the back panel. A fourth filter would have been a nice addition.

I particularly like the size. I had considered a Core P5 at one point but ultimately decided against it because I felt it still wasn't quite as big as I what I wanted. I simply transferred existing hardware from an older mid-tower and at this point, other than adding some modern fans, I have no intention of cramming loads of additional hardware into it. I think a minimalist, more-space-than-you-need look fits the case well.

The glass tint is not too dark or too light but seemingly just right. It gives all the inner LEDs a sublime glow when the case is viewed from just about any angle.

Overall, I'm pleased with the P8. I think Thermaltake will sell many of these once the reviews start showing up. I researched cases extensively before deciding on this one and I think for the price it competes well.

Highly Recommended!

Next to my 50 inch tv this chassis is about 1 tv and a half wide. Solid chassis, I own a Core P3 and a Core P5 setting this up was a breeze. This thing weighs alot with the glass, requires 2 person to move when completely setup with all the water and hardware.

Remove the VESA mount plate to make it lighter if you dont plan to wall mount it.

Remove the filter if you are exhausting air out the back.

Plan to buy yourself a new PCIE x16 3.0 riser as they are a one time use. Handling it too much causes the ribbon to break. I use an empty toiler roll to make my bends wide, the riser stoped working after I mover the riser into a different slot. I moved it with enough care as disarming a bomb, still broke. Again I own a P3 and P5 so Ive gone through plenty of these risers from all sellers on Amazon. Have not tried the super expensive riser Thermaltake just came out, the one where it was demostrated that it can be twisted around.

Good quality/craftsmanship. Out of the box I it is a good baseline for case modding. One could actually daisy chain these together!

**PROS:** nice to looks at, tempered glass; fits standard size PSU and mATX mobo; includes hardware for many different configurations.

**CONS:** seems too big for an itx, but a little bit small for mATX. No mounting hardware for SFF PSU is included.

This will fit a micro ATX (mATX) mobo, but with some overhang, depending on how you mount the board. It fits an itx as well, but an itx mobo will look tiny inside this case... not a bad thing, though, as you'll have tons of space for other stuff. It's easy to mount to the wall if you buy an extra fralt-screen-tv wall mounting bracket like this one: 

Horrible case. Made of cheap steel and plastic. Was really hoping I would love this case but it is really built strictly for looks. Much better cases on the market for the same money. Also their manual doesn't share any information on some of the brackets. Not sure what Thermaltake was thinking on this.

Been building PCs for many years, been awhile since I built in a case that truly felt unique without just being gimicky. The quality is top and despite looking difficult to work with, it's actually easier than many traditional cases. Thermaltake really did well with this case.

Build Specs:
Thermaltake P3 T6
Asus Maximus IX Formula (Front panel 3.0 header doesn't fit next to my x62 rad. I don't blame the case for this, due to unusual position on the board)
7700K
NZXT X62
Asus 1080TI Strix (The GPU length maximum is only required in the (traditional) horizontal configuration. Placing it vertical with the included riser causes no issue with my 11.73" card and push 240mm rad)
4x SSD (double side tape two of them together in the bottom slot below rad, two in the designated bays)

Total build weight for wall mount: 41lbs.

The case looks awesome, especially if your rig is decked with RGB. The quality, not so much My case stand had some defects where the screws they used were too long and protrudes pass the plastic, scratching the crap out of my case when I was putting it back together. The paints on my P3 Red is cheap, very cheap, any kind of scuffle will result in the paint chipping and falling off. The instructions, well, might as well not any. It doesn't tell you what screw size to use where, just tell you to "Lay the case down and put the motherboard on". Thanks thermaltake.

Even though the P3 can fit an ATX motherboard, I wouldnt recommend it if you have a radiator mounting to the right, it will block the SATA connector slots.

Overall, this is just not a case that's worth the price.

So I decided on this case, was kinda of tired of worrying about postive/negative fan pressure, I just wanted something I could "display" with as well. My previous case was a Corsair Vengeance C70 which is coincidentally nearly the same dimensions.
This is well built and nothing feels cheap about it. The metal rods that hold the glass have some serious weight to them. The case provides tons of flexibility for your components. Hiding wires was an absolute breeze as well. The included hardware such as screws and mother board risers werent great. The risers that came with it threaded into the case just fine but I could not get any of the included board screws to thread into the risers. The pitch seemed different but I cannot confirm that. I ended up using some hardware I had laying around for motherboard support. There is a bracket that holds the power supply and it did not seem to fit my thermaltake Smart RBG 850w but I was able to simply flip the bracket and make most of it work. So instead of the bracket fitting around the PSU the PSU just gets bolted to the bracket. Support wise its 100% fine I just could not tell if it was a design intention or flaw. It worked out fine though.
This is a build in progress and I dont have any fear that components I get later will have any issues. I almost wish I had gotten the corner version of this (p90?).

Went for the AH T600 Helicopter chassis.

I am speechless at how sick it is! Even my buddies a d family members can't stop looking at it LOL!

Man oh man where do I start, okay so just to get this out there, this thing is HEAVY. But that's also because I have a lot of stuff in my gaming rig BUT even without it this thing will make you flex them muscles. So have a friend with you to lift it. Because when I did it alone, I found it difficult moving this monster around.

Also do note that both sides have glass panels on them, so be prepared for some cable ties, velcros, cable sleeves, and some cable management skills. Oh and patience!

It's also very spacious inside, as long as you plan your rig ahead with the measurements. It comes with a vertical GPU mount but not the PCIe cable, you need to buy that separately.

I didn't put a dust filter in this so within a month of running it everyday for atleast 5hrs. Of gaming, a started to notice dust buildup. If you don't mind some dustinf here and there, then that should be fine. Gaming rigs are meant to be taken care of anyways.

It also comes with a lot of hardware screws for almost everything that you wanna put in it.

It sure is pricey and a tad bit overkill for a pc chassis but hey, if you have the budget to splurge then might as well get this case.

Beautiful case, easy to put together and the quality of the actual build is insane. This case is amazing for water cooling and putting all your stuff on display. Mounting everything couldn't be simpler. I did have a single problem with this case, though; the VESA mount adapter would not come off with ease. In further detail, the VESA mount thing is attached to the back of the case behind the motherboard by 6 screws. I didn't plan on using the mount and wanted the extra space for cable management so I tried taking it off. I got 5 screws out before getting to the last one, which didn't want to come out. I tried and tried to get the screw out but in the end my screwdriver was stronger than the screw so it ended up stripping the teeth on the screw. I had to use a drill and drill out the screw very carefully as to not scratch my brand new case. I got lucky as the drill bit dug into the screw and ended up unscrewing the screw for me. I wish I didn't have this hiccup as that took off a star in my case. Aside from that, this is a fantastic case that I love having on top of my desk. Also a tip for anyone considering this case: put the GPU AND THE BRACKET on before you install your power supply, as there are screws that are just easier to get to without a power supply in the way.

First of all, I was very impressed with how the machine was packaged. I don't believe any of the "gorillas" that work at any of the shipping companies could damage it during shipping. (The quality of the packaging was evidenced by no leaks in the liquid cooling system.)

Setup was easy: All I had to do is connect it to my 2K monitor, 4K Samsung curved TV, Oculus Rift S headset, keyboard and mouse, WiFi antenna, and power cable.

The VR experience was life-changing, and the machine had no problem playing Fallout 4 VR.

I am a Comp TIA A+ Certified Professional (Computer Technician) and have been working with computers since 1984. So, I can build my own gaming PC. However, when I priced out the parts for this machine, the cost was about $300 more than the price of the machine.

A machine with the exact same specs is being offered on eBay for a price of around $2,900.

No brainer: I opted to buy this pre-built machine, instead of building on, and I am glad I did!

Please note that the machine I received had different components than pictured in the listing photo (MOBO, GPU, SSD, etc.). But, after careful checking, I determined that all of the components had either the same or better specs.

This is a strong indication that the company that builds these machines, and sells them, is a quality company.

I highly recommend this machine for anyone who wants to dive into the VR universe. The quality is excellent and the price represents a good value.

Just be warned: Your life will never be the same again!!!

Incredible case. Its huge... but perfect for building a work of art.

A great case if you know you want something like it. Definitely not a traditional ATX case, but yet not 'out there' like some others.

I wanted a case that you could see the inside easily -- well, you probably aren't going to find anything that does this better than the P3 (or it's bigger siblings). While I wanted an open, non-traditional case … I wasn’t interested in some of the crazier designs. This is still a PC, and not an art installation (for me).
This case overall is a great open design. It lets you secure everything in place far better than just leaving your PC parts scattered on the table, and yes, I have firsthand comparisons to drawn on. It's not perfect by any stretch, but as far as compromises go, none of them made me second guess the decision to go with this case. As I only have M.2 storage mounted directly to my motherboard, I didn't use any of the 2.5 SSD or 3.5 HDD mounts, so I can't really comment on those, but they seem reasonable and effective.
The case certainly is not for everyone. I’m sure most people will want something that protects the innards a little more thoroughly. I only have one major issue with this case, but since this design is a couple of years old, it’s not a surprising one. That issue is the lack of a front panel USB-C connector. I almost didn’t buy this case for that one reason. However, my motherboard has an IO panel USB-C jack, so I decided to go ahead and order this one.
A couple of things to keep in mind with this case though – 1. You will want to use a 360/420mm long radiator, don’t bother with air cooling. 2. You will want a motherboard with an integrated IO panel cover/labeling. There is no provision for mounting a traditional separate ATX IO panel cover.

Pros:
- Puts your fancy-glowy PC parts that you spent a bunch of money on front and center.
- Easy to work on, it has no 'sides' per-se, so nothing blocks access when putting everything together. I didn't even cut myself once, I'm pretty sure that is a first
- Solidly built
- Not super expensive
- Supports radiators.
- Thick tempered glass ‘cover’
Cons:
- If you aren’t using a radiator/water cooling. While there is no technical reason you can’t air cool, doing so means you are leaving an entire 1/3 of the ‘case’ unused. Cosmetically, this just isn’t going to look great, and just leaves you with an unnecessarily oversized case.
- Why-why-why can’t we have gromets on all the wire pass-throughs. Seriously?
- Some tabs/tie-down lugs on the ‘inside’ would be a huge help for securing wires. While it’s not too bad, as there are places to tie down to, more options would be very helpful.
- Well, it is open, so hopefully you don’t have problems with conductive foreign objects, nor small sticky-fingered children.
- A place to mount a small-ish fan to point at the VRM would be helpful.
- No way to mount a traditional ATX style IO panel cover.

Major Con:
- There is one major downside here – that is the lack of a USB 3.1 gen 2/USB-C connector on the front panel array. I think however that I may be able to replace one of the USB 3.0 cables with a replacement to solve this.

 Ich habe lange nach einer Wandhalterung für PC Gehäuse gesucht die nach was aussehen und bin auf dieses Gehäuse gestoßen. Da hat mich das fieber gepackt und ich baute mir ein neues System. Das einzige dumme ist das nur ein 360mm Radi passt für ein Ryzen 3900x und RTX 2080ti nicht ausreichend also experimentierte ich rum und Montierete noch ein 360mm vorne hin. Jetzt bleibt mein System kühl und ich hab Platz auf dem Tisch und der PC verstaubt nicht unterm Tisch. So ein Prachtstück muss man ja zeigen. Das Gehäuse an sich ist Qualitativ ok es gibt aber deutlich bessere wie NZXT oder Lian Li. Aktuelle USB 3.2 Ports wären auch nicht schlecht.

Lässt kaum Wünsche offen, einzig die Positionen der SSD- Befestigungspunkte ( hinter den Luftschlitzen der Kühlung sind/waren für mich störend, da ich dort einen 2ten Radiator nebst Kühlung verbaut habe. Rechts neben dem Halter für die Wandmontage wäre genug Platz für selbige gewesen. Ansonsten super zufrieden, Löcher dort wo man sie wirklich braucht, Kabelmanagement gut gelöst, es sind dort Stege, wo man auch letztlich mit den Kabeln lang läuft, Klebe-Sockel rein, glücklich sein.
Zusammenbau super easy und selbsterklärend, zusammen mit dem TT- RL360 LC-Packet richtiger Eye-catcher !

An excellent case for custom builds. The quality of the case is really good, the tempered glass looks really nice and the case has a lot of space for cable management in the back. A riser cable is include with the case, so mounting a GPU in a vertical position can be done out of the box. Awesome case!

Eins der besten Gehäuse
Ist schnell angekommen und alles gut perfekt top Produkt

Die Qualität ist sehr gut, sehr stabiles Glasspanel.