60 отзывов пользователей o Polaroid Cube Bike Mount
Пользовались
Polaroid Cube Bike Mount?
Поделитесь своим опытом и помогите другим сделать правильный выбор





台座が回転するので、ハンドルに固定してから、左右に向きを調整できます。上向き、下向き気味にしたい場合も、ハンドルバーに沿って回転されることにより調整可能です。通勤に自転車を使っており、何かあった時の証拠となるよう、ドライブレコーダー代わりに使っています。

Dass Polaroid seinen Namen darauf schreibt, zeigt völlige Ahnunglosigkeit
von dieser miesen Qualität. Nie wieder Polaroid.




I suggest placing the mount on your bike and leaving it there. If you install and remove the mount frequently the plastic arms will eventually suffer fatigue failure and crack apart. This is a fault of the basic design of the mount. It should have some simple device, a screw or QR clamp that allows the arms to be tightened on installation and loosened during removal. Pulling the plastic arms apart to push them on or pull them off your bars is going to cause the arms to break, eventually.
The mount comes with rubber shims which go under the mount between the mount and whatever bar you put it on (probably your handlebars). You can use no shim for wider bars but the shim is necessary even on wider bars to prevent the mount from rotating around the bars from road vibration or shock. The shim can easily fall out of the mount when removing the mount from the bars so if you do that a lot be sure you don't lose your shim.
The mount can be swiveled left and right. This is good. But it's done with several interlocking plastic layers which slide against each other and these layers are not very tight. The swivel action is good, it won't move left and right on its own due to vibration or shock. But the camera will shake around in the mount (you'll definitely notice this in your video) and makes a really annoying squeaking plastic-on-plastic noise when you're riding on anything but perfectly smooth asphalt. I wrap a rubberband around the top of the camera in front, under the handlebars, then around the top of the camera in back and that dampens the shaking and eliminates the squeaking. It also adds time and extra steps every time I put the camera into or take it out of one of the mounts.
If you can get a decent low price on this and understand that unless you just install it once and leave it that it will eventually break, it's fine for recreational "action cam" purposes with the Polaroid Cube Act II and its variants with the same form factor. I don't see any other simple mounts for use with this camera so you're kind of stuck with this middling-at-best piece of kit to get it on your bike. It's OK but I wish they'd offer a different inexpensive mount which will stand up to repeated mountings and dismountings and doesn't introduce additional camera shake and vibration.



However I used it as a reference for a model to 3d print a replacement base with a clamp out of ABS and make a few other things, picatinny rail mount, ect.

I don't recommend this product at all. The reviews make it sound more functional than it actually is.

I've attempt to reduce the rattle by placing leaves and other objects I find along the trail under and behind the camera while riding, but to no avail.
My next step is to tape or glue a small velcro "dot" or other self-adhesive object inside the clip on which the camera can sit to try to alleviate the rattle.
Otherewise,this is a great little mount, holds my camera very steady, and alleviates the need to hold while filming.









Лучшие цены сегодня на Polaroid Cube Bike Mount
График изменения цены Polaroid Cube Bike Mount
Характеристи Polaroid Cube Bike Mount
Общие характеристики | |
Тип : | крепление |
Назначение : | на руль велосипеда |
Совместимые бренды экшн-камер.портативных видеорегистраторов : | Polaroid |
Диаметр трубы для крепления : | 25 |
Материал : | пластик, резина |
Поворотный механизм : | есть |
Информация о характеристиках носит справочный характер.
Перед покупкой уточняйте характеристики и комплектацию товара у продавца