Отзывы о Материнская плата ASRock H410M/ac

Плата куплена за 6 399 р. и для меня это самый большой ее недостаток. Неприятно отдавать такие деньги за изделие на H чипсете. Есть, конечно, варианты дешевле, но там меньше фаз питания и мне это не подходит, т.к. в данный момент стоит i3 10100 с планами дальнейшего апгрейда на i5 10400. При установке плата похрустывает, видимо текстолит тонковат. Так же хлопот даставили очень тугие разъемы питания мат. платы и процессора, с большим трудом удалось подключить к ним блок питания, при этом плата неприятно прогибалась и похрустывала. Аудио и микрофонный выходы тоже тугие, штекеры фиксируются как будто не до конца. Неудачно расположены SATA порты - они перекрываются видеокартой, так что если захотите добавить/поменять накопитель, то видеокарту, вероятнее всего, придется снимать. Из видеовыходов только HDMI, но для меня это недостатком не является.

В завершение хочу сказать, что несмотря на некоторые проблемы и нюансы, плата справляется со своими задачами хорошо, имеет неплохую систему питания, достаточно удобный, хоть и не совсем корректно переведенный биос, ну и wi-fi модуль избавляет от необходимости тянуть кабель по квартире. Учитывая сложившуюся ситуацию на рынке и сравнение с другими производителями, могу смело рекомендовать к покупке.

В целом доволен, материнка не плохая, работает в связке с i5 10400f и gtx1080

На следующий день после покупки уехала на проверку качества, успел только установить винду и установить браузер.

Проблема оказалась в том, что были загнуты усы на соккете, поэтому при покупке обязательно проверяйте всё тщательно

Хорошая мамка на младшем чипсете, бралась под i3 10100...

When I built my gaming rig, the only thing was getting the right Ram for this board. So I saw a video on YouTube about the only Fast sticks of Ram that fitted this board perfectly at that time were G.Skill 16 GB DDR4-3200 CL16 G.Skill RipJaws V Noir Series, these little wonders saved my life and it is my new build that I'm writing this review on and have had this build for a couple of months now. I cannot believe the power of this motherboard, easy to setup and if like me you have a really nice case to put it in? You'll be rockin' along. The AI shield can be cumbersome, but if you trim off the sticky outty metal bits you'll have no problem slotting in the motherboard.

On my build I have Ryzen 5 2600 CPU, 16GB of G.Skill Rip-Jaws Ram, make sure you put the ram in the right slots, for two 8GB sticks they should go into slot 2 and slot 4. Also on my build is 650What Watt even semi modular Power Supply and for graphics a Nvidia 1050ti. The operating system is Peppermint OS 10 Linux, many people will be asking as to why? As Linux has not got very many games. On the contrary, we now have Steam Play which is also called Proton and the wonderful people at Valve who gave us all Steam, worked with the wonderful people at Code-Weavers, who gave us WINE which stands for Wine Is Not A Emulator. WINE enables us to run Microsoft stuff in Linux, with the help of some very clever programmers, we are able to play Windows games in Linux. I will never ever own a Windows machine ever again for gaming, simply because I get better performance here in Linux and I know that I won't have to start paying for using a Operating System, like Windows will be in the next year or two. Windows or Microsoft want you stream their OS for a weekly or monthly fee, Linux is yours to own and do whatever you want with, plus it's free.

End of speech, glad I got that off my chest, back to the review. Inside the bios of this, set your ram up to read fastest speeds as Ryzen processors like the Ryzen 5 2600 like fast Ram, the faster the better. I also bought a Icy Dock to house four SSD drives, though this motherboard only has four Sata inputs, I have had to give up one Sata input for my DVD drive, which came out of a build that the motherboard itself had given up the ghost.

Building your own desktop has never been so easy, this board I can highly recommend as I'm going to build another to use as a streaming PC, through a onboard capture card. Using the same motherboard, Case, Ram, Power Supply, below is the parts I highly recommend to go with this build.

RAM https://www.amazon.co.uk/gp/product/B015FXXBW0/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

ICY DOCK https://www.amazon.co.uk/gp/product/B00V5JHOXQ/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

MODULAR HYBRID PSU https://www.amazon.co.uk/gp/product/B06WVWXPVZ/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

CASE https://www.amazon.co.uk/gp/product/B01LW3YN1I/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Choice of Ryzen Processors https://www.amazon.co.uk/gp/product/B07B41WS48/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

Choice Of SSD Drives https://www.amazon.co.uk/gp/product/B073SBZ8YH/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Fans I recommend https://www.amazon.co.uk/gp/product/B078JW73WF/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

These are all the things I have in my case and of course the choice is yours, you don't have to copy me, but I just wanted to give you an idea of the quality stuff there is here on Amazon.
Unfortunately I don't do overclocking so no point in me recommending a water cooler, as never use them. This board is a pleasure to build with and the speed of this is just spectacular. Highly Recommend to new and advanced PC builders.

久々の自作です。
メモリースロットが４，M.2スロットが２，ということでこの製品を選択。
Ryzen3-2200Gと組み合わせました。SSDもNVMe1.3の物を組み合わせました。
他にドライブ類を接続して無いので、マザーボードからは、電源やスイッチ類以外のケーブルが生えてない状態です。
12/4に購入、BIOS Verはこの時点で最新のP1.6でした。

このMBはM.2-SSDスロットが2個ありますが、slot1はPCIe Gen3 x4対応ですが、Slot2はSATAまでのようです。
また、M.2 をとめるネジ、が1個分しか付属していません。
最初からM.2 SSDを2個ーと考えている方はご注意ください。
最初手持ちの電源と組み合わせましたが、古いAopenのTFX電源（P4対応、ATX2.01）200WではBootせず。
古いPS3-ATX（全長が短いATX電源) 2.03 300Wでは無事Boot

Slot1はAMD純正CPUクーラーからの風がかなり当たる位置にあります。

私だけかもしれませんが、USB メモリーでWindows10をインストールしようとして
Bootの順番を「USBレガシー」「UEFI USB」の順番にしてしまっていて、
最初Windows10が「このドライブにはインストールできません」連発で、インストールできず悩みました。
「UEFI USB」でWindows10インストールUSBメモリーを起動することで問題なくインストールできました。

なお、仕様上、M.2のPCIe SSDは認識していても名前がBIOSに出ないため、最初BIOSかハードウェア側の問題か？
とかなり悩みました。BIOS側では、M.2に関してはBIOSのストレージ項目でもほぼ触る所はありません。
Bootの順番できちんとM.2の（この場合PCIe SSD）が選択できる場合は、BIOSがきちんと認識しているようです。
（Windowsのインストーラからドライブ見えて、パーティーション操作できた時点で問題無いはずではある）

また、これはUbuntuのビデオドライバとRyzen3-2200Gの兼ね合いと思いますが、
Ubuntu18.04LTSのライブUSBでは、起動時に手動でオプションを入れないと、GUIは画面が崩れるようです。

----
その後です。古いP2.0以前のBIOSはP2.0経由でP3.0以降にUPDATEの必要があり、そのとおり実施しました。
↑のRyzen3G2200から、Ryzen7-3700XとRX570にアップグレードしたところ、VGAカードを認識せず、BEEPｘ5（VGAカード初期化不能or無し）でBIOSも起動市内状態に。

CPUだけ、以前のRyzenGに戻したら正常に動作。（この場合ｘ8レーンに強制的になるためと思われる）
借りたRyzen5-1700Xではｘ16レーンで正常にVGAを認識し動作。

VGAカードを外側の4レーンのスロットや、PCIEx16スロットをｘ8ｘ2レーンに制限すると正常に動作。

結果的に、なぜか「第3世代Ryzenでは、PCIEスロットがｘ16ではVGAカードを認識せず、
BIOSで事前にｘ8ｘ2に制限するかｘ16スロット以外にVGAカードを装着しないと動作しない」、
という謎の症状になりました。

メーカーに問い合わせたところ、この個体の不良のようで、
「こういう不良もあるんだなあ」という感じです。

Contacted ASROCK who say they will fix under the EU 2 year Warranty law but this needs to be sent to the Reseller (Amazon) to be processed otherwise I would have to pay postage to Netherlands. Contacted Amazon & they refuse to return Item as they say it has no Warranty at all, even though it is under manufacturers warranty.
I am very disappointed with Amazon.

Has an issue not booting after shut down, had to press CtrAltDel to get it going so got replacement which still had this issue. Not the sellers fault as they were both sealed & new.
Once on it worked well, but after updating the bios to the 2.0 one from December 2018 it does not boot at all, does not display anything, tried all reset methods with no luck.
Not happy as this Asrock motherboard worked much better than my Gigabyte z170x with i7 6700k it replaced which was suffering micro stutter in games.
Can't return as i've had it for a few months.
Will have to try MSI or Asus next time

Nutze das Board mit einem Ryzen 5 2600 und 16 GB Ram von G.Skill RipJaws.
Ich bin kein Fan davon ein Board aufgrund des niedrigen Preises direkt abzuwerten. Ich war mir nicht sicher ob ich zum B450M oder B450 greifen soll, hab mich aber dazu durchgerungen das die Micro-Variante ausreicht. Ich bin sowohl mit dem Board als auch mit allen verfügbaren Funktionen voll zufrieden.
Die Schnittstelle für die M.2 SSD nutze ich leider nocht nicht, da ich von dieser Technik erst erfahren habe als ich mir Board Rezenssionen durchgelesen habe, da war die SATA SSD aber schon bestellt und geliefert. Wird aber definitiv noch nachgerüstet.

Ich kann das Board trotz des niedrigen Preises, oder gerade deswegen, nur empfehlen.
Sollte sich in den kommenden Monaten etwas an meiner Zufriedenheit ändern werde ich es hier mitteilen.

Big fan of this feature-packed MATX board.

Highlights for me:

1. 2 NVMe drive slots along with 4 SATA ports (plenty of storage options)
2. Compatibility with AMD Store MI, which allows you create your own SSD/standard drive hybrid storage solution. In short, you will be able to bring down the cost of high speed storage access by combining a small SSD with a large standard internal drive.
3. Excellent overclocking bios. RAM and CPU overclocking easy to do, and VRM heatsinks are up to the task
4. Future-proofed somewhat. You can flash the bios and enable the latest 3000 series Ryzen to run on this. Say you are on a 2600, you could move up to as high as a 3900X without a full motherboard transplant.
5. Excellent sound chip with some high quality chokes
6. Lots of USB: 2.00, 3.00 and the latest C supported.
7. Nicely laid out board, and nice to look at.
8. 4 RAM slots

At this price-point it's hard to fault. I would say if you are bit more serious about overclocking, the ASROCK Mortar B450M board is better equipped, but that costs a good chunk more. For me this seems fine, although those VRM heatsinks feel like they are being worked hard when pushing component performance.

Overall, a great option for a Ryzen 2000 chip. 100% satisfied.

The board comes well packaged, with all the necessary bits. Working on the board wasn't hard, it's layout is good and the SATA ports are thankfully at right angle to the board face. The I/O cover is not sturdy at all, and it gave me a problem with one of the hooks stuck in the HDMI port, but taking the board out and solving that issue was easy enough to do. Installing the board is easy, so is putting in the CPU, GPU, RAM and connectors. It's worth being careful when putting in the 24-pin connector, so the board doesn't flex too much, although mine stood up to it. Setting the right ram speed in the BIOS was quick and easy. The BIOS gives you lots of information and settings to use.
I recommend ASRock's A-tuning software, it works excellent, it gives temps and allows you test fans and set fan curves.
All in all, I'm very pleased with the board, recommend.

After a long and draining period of troubleshooting I have finally reached the conclusion that the motherboard itself has been the issue in my PC.
I watched a Linus Tech Tips video in which he build a computer using this same motherboard and a few other bits which lead me to order mainly the same parts as him. After I’ve built it it so happens that I had to come back from furlough on full time and did not have the time for about three weeks to use my newly built PC enough to realize that the PC did not always POST successfully and that it would require at least 5 or so times for the PC to be turned on and then of until it would POST and boot successfully. After spending all of my days of troubleshooting, rebuilding it, buying a new PSU to test as see if maybe the other PSU was bad, buying a motherboard speaker to check for beep codes, numerous test with the motherboard built outside the case, components taken of and put back in and so on and so forth, after all of that painstaking process and hours of labor wasted, I can safely say that the motherboard is faulty and either somewhere in shipping or perhaps before it even left the factory, the motherboard died and ended up in my hands dead on arrival (DOA). I’m truly disappointed as the board itself is more than great, great I/O, great cooling and when it does POST, great apps for windows and great BIOS. I wish I could recommend it, however because of the state it arrived to me I urge you not to purchase it and instead go for a manufacturer with a higher trust factor.

This motherboard is the perfect budget B450 board. No bells and whistles, but does what it needs to very well.

PCB is reassuringly thick and looks great with subtle black/silver aesthetic. This board has everything you need for a solid PC build; 4 RAM slots, 2 PCIE, 2 M.2 (only one ultra), plenty of I/O (especially USB). In particular this board has an incredible VRM design for this price point with chunky heatsinks to keep the VRMs cool under load. Temps keep well below 70 degrees when overclocking my Ryzen 5 3600 CPU, feels like the board has plenty of headroom for even more agressive overclocks or higher TDP CPUs.

Audio output from this board is surprisingly good, don't feel any need for a discreet audio card. If required a Wifi and Bluetooth card can behad for £10.

Word of warning to RGB users, Asrock's RGB software (Polychrome) is pretty dysfunctional and on the whole frustrating, be ready to have to fiddle to get it working.

Overall highly recommended for anyone who needs a budget B450M board.

I used this board on a budget build for my son's gaming pc and if was a pleasure to work with.it has pros an cons as amatx board's are always a compromise due to smaller size so less physical parts. Pros for me are small size .high surface area vrm heatsinks .good price . Cons were, I would have liked more fan controllers ( however I got around this by getting a 3x case fan deal with an external fan controller ) and no RGB on the board. It works fine out of the box and is now a reliable pc
Final spec
ryZen 5 1600, 16 GB ram,gtx 1070, 120 GB SSD for Windows, 3tb HDD for games.

Item arrived in good time as expected. Upon opening item corner of box was damaged. Proceeded to install new board, using all new parts; corsair ddr4 vengance x2 8gb ram, amd ryzen 2600 chipset, corsair 650i psu and samsung ssd 250gb.

The power supply was evidently working as the power light on the key board was on. Tried an independent psu test as reccomend by corsair, this checked out.

Maybe insufficent psu, removed graphics card and used an old card; asus amd radeon hd 6670, still getting power nothing on monitor and still there is a light on the keyboard.

Perhaps the amd ryzen 2600 chip was misaligned or incorrectly installed. Checked the pins, no bends and all present, checked the arrow matches. Re-installed chip.

In conclusion; can only conclude the either the board or chip are the issuse here after multiple tests carried out to determine source of issue. It is unlikley that the chip is the issue due to correct istallation and no noticeable damage to pins, although this is not totally conclusive. On the basis that all possible tests were carried out correctly and thorouhly, it can only be concluded the issue is that no power is reaching the motherboard and is there for Dead on Arrival (D.O.E)

Great motherboard and does everything its meant to so no worries there, when I first got it I didn't know you had to put the ram in slots A2 and B2 if you have only two and it isn't very clear in the manual so I was getting blue screened restarts due to this, its only that I googled it I found out I didn't in fact have a broken motherboard and I even went as far as reinstalling windows 10 and thinking maybe my ram wasn't working due to it restarting.
So if you buy this motherboard make sure you put the ram in these slots.

What can I say about this board?
Well not really alot since it's just a motherboard.

But it is an all round good board for Ryzen 3xxx, Comes with all the features I needed alongside support for 64GB of ram which is important to me as it'll be used in a server.

Also big props to amazon for actually upgrading this board to the required bios for Ryzen 3000!

Realtek audio drivers will make the rear panel 5.1 audio to stop working, the only way to get 5.1 is by using the Windows default drivers which left you with crapy audio quality. The Realtek control panel doesn't start (Please note that these two problems are more Windows fault as forums say the update of windows was the one which brought the problem). I ended buying a dedicated audio card.
The Ultra M.2 PCIe NVMe SSD slot only supports a range of models, usually the most expensive ones. If you buy one the manual says is supported you might end regretting the buy. Try to go to the website and get the exact model they say. Overall I and spending around 70 Euros more to get everything working. better spend that money in a better MOBO.

Nach mehreren Versuchen mit diversen "High-End-Borads" für meinen Ryzen 2600 - bei welchen es kein Hersteller geschafft hatte, eine aktuelle Bios-Version - auszuliefern - bin ich letzendlich hier gelandet. Und was soll ich sagen? - Ryzen drauf - läuft! und zwar tadellos! Das Board kommt ohne Schnickschnack aus, das Bios ist übersichtlich gestaltet und hat alles, was ein Normaluser braucht. (Ich übertakte nicht). Ich hab'noch 16 GB Ram verbaut und ein Xubuntu 18 OS darauf installiert.
Zusammen mit einer GTX 1060 auch perfekt zum Zocken: Über die neue Steamplay.-Funktion sind auch bisherige "windows-only"- Titel kein Problem....Kaufempfehlung!

I have ordered this because of my old motherboard not accepting Ryzen 2nd gen processors. I installed my Ryzen 2600X into this motherboard and it booted no problem at all with no BIOS update needed. There is a nice selection of USB ports on this board also and the fact that it had 4 x RAM Dimms makes it a perfect little micro atx board for first time PC builders.

Just built a PC with ASRock B450 mobo, Ryzen 7 CPU and Samsung EVO970 NVMe as the windows boot drive. Worked first time. I spent ages trying and failing to get another mobo to work but I'm not sure where the problem was but NVMe compatibility is not assured. N.B. NO VIDEO OUT from mobo with Ryzen processor. You need a Graphics card.

Great AM4 board. Paid about £62 for it.

It has two M.2 slots on the board which is a great feature at this price point and can help keep builds tidy as no cables are needed.

As it turns out, this motherboard was dead on arrival. I finally received all of my parts (delays due to the covid-19 issue), and once set up to go, the PC is dead. After a significant amount of investigating and many attempts to get this to work, the bottom line is that the MOBO is dead.

loved the two seperate m.2 slots one nvme and the other ssd. seeing as the board was amd 450 chipset we got a free download of store mi which allowed to us to use a 128gb m.2 ssd fuzed with a 2tb western digital hard drive and 2gb ram giving me 2tb as rapid storage so thats where all the games are loaded. it really is worth every penny we spent on it.